Glitter Snow Ornaments

Glitter Snow Ornaments

This is a perfect craft to keep for yourself or give to a friend as a gift. This Christmas ornament speaks for itself. It's glittery and beautiful. Acrylic paints and styrofoam balls put this ornament together.

Materials:

  • STYROFOAM* Brand Foam:
    • Balls, one each size: 3", 2", 1-1/2"
  • Black craft foam, 1/2 sheet (hats only)
  • Glitter: iridescent white micro, black (hats only)
  • Beads: black, 4mm, two; pink, 6mm, two; pearl, 6mm, three
  • Wooden dowel rod, 3/16", 6" length
  • Wooden skewer
  • Acrylic paints: pearl, rose, orange
  • White glittered chenille stem, 2" length (earmuffs only)
  • White glittered pom poms, 1/2", two (earmuffs only)
  • White ribbon: curling, 1/4" x 1/2 yd.; wire-edged sheer, 1" x 1/3 yd.
  • White ribbon roses with leaves, 1" across, one to two
  • Serrated knife
  • Candle stub or paraffin
  • Pencil
  • Ruler
  • Paintbrushes: flat, liner
  • Disposable palette
  • Water basin
  • Paper towels
  • Scissors
  • Craft knife
  • Craft snips
  • Floral wire
  • Low-temp glue gun and glue sticks
  • Thick, white craft glue
    Pattern

 

Steps:

  1. Wax serrated knife with candle stub or paraffin; cut 1/4" from top and bottom of 2" ball. Tightly twist balls together to form snowman; use glue gun to secure.
     
  2. Use craft snips to cut dowel in half for arms; paint pearl. While still wet, sprinkle with white glitter. Push cut ends into scrap piece of foam to dry.
     
  3. Insert skewer into bottom of snowman. Holding skewer, spread craft glue evenly over entire snowman. Sprinkle surface with white glitter; use fingers to gently press glitter into glue. Stick skewer into scrap piece of foam to let glue dry.
     
  4. Use glue gun to glue arms into body as shown. Glue and gently press beads into foam for eyes, cheeks, and buttons.
     
  5. Use craft snips to cut 1" from pointed end of skewer for nose. Paint orange; glue to face. Use liner brush to paint tiny rose mouth.
     
  6. Trace patterns onto black craft foam; cut out with craft knife.
     
  7. For snowman, overlap short hat crown edges 1/4"; use glue gun to secure. Use craft glue to glue top inside crown and crown to brim; let dry. Apply craft glue to entire hat and sprinkle with black glitter; let dry. Glue hat to head. Glue short length of curling ribbon around hat for band; glue ribbon rose to band. Tie sheer ribbon around neck. Tie remaining curling ribbon around neck; use scissors blade to curl ends.
     
  8. For snowlady, make a cut from edge of hat crown to center. Overlap edges and bend crown into shallow cone; use hot glue to secure. Use craft glue to glue crown to brim. Apply craft glue to entire hat and sprinkle with black glitter; let dry. Glue bonnet to head. Center sheer ribbon over top of bonnet; tie under chin. Spot glue knot to chin to secure. Tie curling ribbon around neck; use scissors blade to curl ends. Glue ribbon roses to hat brim and ribbon knot.
     
  9. For snowbaby, bend chenille stem into a "U"; glue ends to sides of head. Glue pom poms over chenille stem ends. Tie sheer ribbon around neck. Tie curling ribbon around neck; use scissors blade to curl ends.
     
  10. Cut 3" length from wire for hanger. Bend wire into hook; glue into top of head.

 

®™ Trademark of The Dow Chemical Company ("Dow") or an affiliated company of Dow. For more project ideas, please see styrofoamstyle.com.

  1.  

Your Recently Viewed Projects

Leave a Comment

Rate

Cancel Reply to Comment

Thanks for your comment. Don't forget to share!

Close

Report Inappropriate Comment

Are you sure you would like to report this comment? It will be flagged for our moderators to take action.

Thank you for taking the time to improve the content on our site.

Join our community of 5 million crafters!

Thank You for Signing Up!
There was an issue signing you up. Please check your email address, and try again.

More from "Ornaments"

 

 

Close Window