Search Term

Enter a search term (optional)


Select One (optional)

Difficulty Level

Select One (optional)

Estimated Cost

Select One (optional)


Select as many as you like (optional)

  • Fabric Crafts
  • Paper Crafts
  • Craft Foam
  • Pipe Cleaner Crafts
  • Clay & Sculpting
  • Nature Crafts
  • Wood Crafts
  • Beads & Jewelry
  • Recycled Crafts
  • Painting & Coloring
  • Food Crafts
  • Plastic
  • Mixed Media/Miscellaneous
Time to complete

Select One (optional)

Primary Technique

Select One (optional)


Select One (optional)


Select as many as you like (optional)

  • Spring
  • Summer
  • Fall
  • Winter
Age Group

Select as many as you like (optional)

  • Toddlers
  • Preschool & Kindergarten
  • Elementary School
  • Pre-Teens
  • Teens


Free Offer
20 Bracelet Patterns: Macrame Bracelets, Friendship Bracelets, Hemp Bracelets, and More

Friendship bracelets are all the rage! Get in on the trend by learning how to make friendship bracelets using the instructions in this FREE eBook!

Bonus: Get our newsletter & special offers for free. We will not share or sell your email address. View our Privacy Policy

Simple Unique Clay Necklace

This simple unique clay necklace from Jacquard Products is a beautiful piece of jewelry that you will be proud to have crafted yourself. Homemade clay jewelry hardly gets easier than this.


  • Pearl Ex powders: I've used Spring Green, Misty Lavender, True Blue, Flamingo Pink and Super Copper
  • Jacquard Gold Lumiere
  • Black Premo Sculpey polymer clay: three 2 oz. packages, conditioned and ready to use.
  • Small foam-type brush
  • Bamboo skewers: medium & large (about the size of a chopstick)
  • Clay dedicated pasta machine or something to roll the clay flat.
  • Sculpey Clay blade or craft blade.
  • Small pieces of medium sandpaper
  • Gap filling instant glue
  • Buna Rubber Cording material (or any black cording): 14".


  1. Roll black clay about 3/8" thick (#1 on pasta machine).
  2. Cut out basic forms, roll clasp bead.
  3. Set aside about 1" ball for coils.
  4. Roll rest of clay out very thin (#6 or 7 on pasta machine).
  5. Finger paint on the Pearl Ex.
  6. Tear small pieces of this and press into place on forms, overlapping each piece and the edges.
  7. Poke holes with skewers for linking and add small pieces of clay to back of top edge to allow for holes for cording.
  8. Roll thin tubes of clay and wrap around the large skewer about an inch. Make 3 coils on the medium skewer.
  9. Bake according to package directions.
  10. Using water-wet brush, dip into Lumiere and wash the top surfaces. Use towel to daub excess. Allow to dry.
  11. Cut 3" piece of cording, thread large coil onto it and pass each end through one of the necklace pieces. Add small amount of glue to each end and quickly thread back through the coil.
  12. Cut the remaining cord so one side is two inches longer than other side. Glue into place at top parts of necklace pieces.
  13. Allow to dry and adjust cord lengths for desired wearing length.
  14. Thread coils onto each length to slide down and cover where the cord is glued into clay shapes.
  15. Thread last coil onto the loop side of the closure. Trim end at an angle, dot with glue and push back into coil to form a loop to fit the clasp bead.
  16. Glue other end of cord into clasp bead.
  17. To Assemble: Take a 3" piece of cording and thread through one of the holes in your clay. Thread the large coil onto this clay and thread through the other clay piece you are attaching. Add a small amount of glue to each end and pass the ends back through the coil. I chose to leave the excess cording ends, but you can trim them.
  18. Cut the remaining cording in half, leaving 2 extra inches on the loop side of the necklace, and glue into the wedged holes at the tops of each piece. When these are dry, determine how long you wish the piece to hang when worn and trim the cord, (leave 2 extra inches on the loop side). Thread a coil on both pieces of cording to slide down and cover the junction of the cord and the top of the clay piece.
  19. Trim the end of the loop end at an angle and thread a coil on it, holding the coil about 3 inches from the end of the cord. Add a drop of glue to the angle-cut end, and loop it back into the coil forming the loop for your clasp.
  20. Glue the clasp bead onto the other end of cord. I glued the glass pieces into place - and waited PATIENTLY for the glue to dry before trying on my new necklace!


Your Recently Viewed Projects

Free projects, giveaways, exclusive, partner offers, and more straight to your inbox!

Include a Photo Include a Photo

Click the button above or drag and drop images onto the button. You can upload two images.

Cancel Reply to Comment

Thanks for your comment. Don't forget to share!



Report Inappropriate Comment

Are you sure you would like to report this comment? It will be flagged for our moderators to take action.

Thank you for taking the time to improve the content on our site.

Project of the Day

Paint Chip Valentine Wreath

Use paint chips in pinks and reds to create a fun Valentine's Day wreath at little to no cost! Lish uses the paint cards with 4… See more

Something worth saving?

Register now for FREE to:

  • SAVE all your favorite crafts
  • ADD personal notes
  • QUICKLY reference your crafts


Connect With Us

Facebook Google Plus Instagram Twitter Pinterest
Twitter Blog Email RSS

About Us Advertise Contact Us FAQ Keyword Index Privacy Policy Share Your Project Subscribe Terms of Service Unsubscribe

---- 1 ----


Images from other crafters

There are currently no images from other crafters.