Search Term

Enter a search term (optional)


Select One (optional)

Difficulty Level

Select One (optional)

Estimated Cost

Select One (optional)


Select as many as you like (optional)

  • Fabric Crafts
  • Paper Crafts
  • Craft Foam
  • Pipe Cleaner Crafts
  • Clay & Sculpting
  • Nature Crafts
  • Wood Crafts
  • Beads & Jewelry
  • Recycled Crafts
  • Painting & Coloring
  • Food Crafts
  • Plastic
  • Mixed Media/Miscellaneous
Time to complete

Select One (optional)

Primary Technique

Select One (optional)


Select One (optional)


Select as many as you like (optional)

  • Spring
  • Summer
  • Fall
  • Winter
Age Group

Select as many as you like (optional)

  • Toddlers
  • Preschool & Kindergarten
  • Elementary School
  • Pre-Teens
  • Teens


Free Offer
24 Thanksgiving Dinner Recipes and Fall Craft Projects

This FREE eBook is brimming with Thanksgiving craft projects and recipes to make your Thanksgiving dinner celebration a hit!

Bonus: Get our newsletter & special offers for free. We will not share or sell your email address. View our Privacy Policy

Autumn Reflections Candle Holder

By: Cindy Groom-Harry and Staff for AMACO

Create an elegant Autumn Reflections Candle Holder from wire mesh from AMACO.

Autumn Reflections Candle Holder


  • AMACO® WireForm®:
    • 6" x 8" piece of Impression Mesh, Copper, 1/8" pattern
    • 5" x 6" piece of Sparkle Mesh, Aluminum, 1/8" pattern
    • 5" x 6" piece of Designer’s Mesh, Brass, 18 mesh
  • AMACO® Fun Wire™: 14 ft. of Brown; 24 gauge
  • 6" length of 5/16" diameter dowel
  • Two large wooden craft disks (1/2" x 21/2")
  • October Brown spray paint
  • Tea light candle
  • Glue gun & glue sticks
  • Pencil
  • Paper
  • Craft snip or wire cutters
  • Needle nose pliers
  • Ruler
  • Drill with 5/16" bit

AMACO® WireForm® and Fun Wire™; Forster® Dowel and Craft Disks; Design Master® Color Tool® Spray Paint; and Adhesive Technologies Professional I Glue Gun and Crafty Magic Melt® Glue Sticks are recommended products.


LEAVES: (Note: Before cutting leaves from Impression Mesh, cut off a 2" x 6" piece and set aside.) Trace and use craft snip to cut two leaves from the Impression Mesh according to pattern. Similarly, cut two leaves from the Designer’s Mesh and Sparkle Mesh.

  • For center vein of leaf, cut a 6" length of Fun Wire™. With one leaf, insert Fun Wire™ through mesh at base of leaf allowing 1/2" to extend from base for stem. Insert wire back and forth along the center of mesh leaf at 1/4" to 1/2" intervals, bending and scrunching wire between intervals to add character. Bend end of wire over at point of leaf and trim if necessary.
  • Cut a 24" length of wire. To encase the leaf edges, fold wire in half and carefully (so as not to pull out mesh strands) insert each end through mesh at point of leaf and twist wires together once to secure. Then, use wire to "sew" around both sides of leaf by inserting wire through mesh, wrapping wire around outside edge of leaf and reinserting through mesh at 1/4" to 1/2" intervals, ending at base of leaf. Twist ends of wires onto stem and trim stem to 1/4".
  • For remaining veins, cut 3", 4" and 5" lengths of wire. Fold 3" length in half to find center, place wire under center vein 11/4" from point of leaf and cross wires over center vein to secure. Insert wire at an angle back and forth through mesh leaf at 1/4" to 1/2" intervals, bending and scrunching wire between intervals to add character. Bend end of wires over at edge of leaf and trim if necessary. Repeat using the 4" and 5" length, spacing approximately 11/4" apart.
  • Repeat procedure to make five more leaves, but don’t trim the stem on one leaf.


  • Drill a 5/16" hole in the center of two craft disks. Glue disks onto each end of dowel with rounded side of disks toward dowel. In well-ventilated area, spray candle holder with October Brown paint and let dry.


  • (Tip: To glue flower leaves to holder, use the lid of the spray paint as a working tool.) Set holder on top of lid (the flat edge setting on top of the lid will actually be the top of the candle holder). To make flower, attach a leaf (with trimmed stem) to rounded side of disk close to dowel using glue gun. Bend leaf down over paint can lid to shape. Similarly, attach four more leaves to disk, overlapping leaves approximately 1/2", and bend to shape. Remove candle holder from lid and set upright.
  • With long-stemmed leaf, bend stem around base of dowel, bend to shape and tack glue leaf to craft disk.TENDRILS: Cut two 21" lengths of wire. Fold each in half, spiral wrap ends around pencil or dowel, remove and then bend and scrunch wire to add character. Twist folded centers together and glue to base. Bend and shape tendrils as desired.


  • Place the 2" x 6" piece of Impression Mesh (from step one) over edge of ruler and fold in half to form a 1" x 6" strip. Roll and glue strip into cylinder just slightly larger than tea light. Glue holder, with folded edge up, into center of flower. Place tea light candle into holder.

Autumn Reflections Candle Holder

Your Recently Viewed Projects

Free recipes, giveaways, exclusive, partner offers, and more straight to your inbox!

Include a Photo Include a Photo

Click the button above or drag and drop images onto the button. You can upload two images.

Cancel Reply to Comment

Thanks for your comment. Don't forget to share!


Report Inappropriate Comment

Are you sure you would like to report this comment? It will be flagged for our moderators to take action.

Thank you for taking the time to improve the content on our site.

Project of the Day

Decorative Globe Anthropologie Knock-Off

Don't throw away your money on expensive boutique decor - reuse old materials and make your own instead. The end result will be a far… See more

Something worth saving?

Register now for FREE to:

  • SAVE all your favorite crafts
  • ADD personal notes
  • QUICKLY reference your crafts


Connect With Us

Facebook Google Plus Instagram Twitter Pinterest
Twitter Blog Email RSS

About Us Advertise Contact Us FAQ Keyword Index Privacy Policy Share Your Project Subscribe Terms of Service Unsubscribe

---- 1 ----


Images from other crafters

There are currently no images from other crafters.