3D Style Wall Art Trees | FaveCrafts.com

Follow Us on Facebook

Get updates from FaveCrafts.com posted directly to your News Feed.

Free Offer
Cheap Home Decor: Crafting with Paper

If you are on a craft budget, have a look at this collection of 60 low-cost craft projects, sorted into categories such as needle craft, home decor, crafts for kids and more

Bonus: Get our newsletter & special offers for free. We will not share or sell your email address. View our Privacy Policy

(3)

3D Style Wall Art Trees

By:

Give any room in your house a unique feel with these 3D Style Wall Art Trees from Gloria Uhler.  Using a stencil, you can create one or more trees on a solid colored wall for wall art decor that's sure to "stand out"!

3D Style Wall Art Trees

Materials:

  • Victoria Larsen stencils
  • White Tub & Tile Caulking and gun - Lowe’s
  • Painters tape - Lowe’s
  • Yardstick or dowel
  • Putty knife
  • Ranger Perfect Pearls Palettes pigment powder - Michaels


Instructions:

  1. Plan the number of trees you will create and their size. If you’re going to angle some trees, tape a yardstick or dowel against the wall as a guide and follow it as you position your stencils.

    3D Style Wall Art Trees
     
  2. If you won’t be using the largest tree trunk, you can cut it in half vertically to create a size that will work for your project. I taped mine back together making it only slightly larger than the smaller trunk. I also angled it so it tapered at the top.

    3D Style Wall Art Trees
     
  3. The directions included with the stencils suggest using joint compound. Because I’ve successfully used tub caulking for this kind of job before, I chose to use it again. A caulking gun makes the application convenient. Fill in the center of the trunk stencil then use the plastic putty knife to distribute caulking to all open areas. Work in a well ventilated room and occasionally spray a good quality room deodorizer as you work to minimize the caulking smell. Glade Fresh Linen almost completely eliminates the odor.

    3D Style Wall Art Trees
     
  4. Create all the tree trunks first by adding additional sections as you work up the wall and reach the desired height. Hold the stencil to the wall with painters tape.

     3D Style Wall Art Trees
     
  5. If you like a lot of texture, the more irregularities in the caulking surface the better. Create a tree bark-like effect by dabbing at the caulking with the straight edge of the knife once the stencil is filled. Running the knife horizontally across the stencil will also create realistic ridges.

    3D Style Wall Art Trees
     
  6. Because you would have to wait for one trunk section to dry before repositioning the stencil again, you may want to cut off the blank margin on one edge of the stencil leaving it open at the bottom. This will allow you to align the stencil edges with the finished edges of the previous trunk and continue working. Use the knife to blend the joined ends of added trunks. Keep an oversized towel and a sink filled with sudsy warm water to wash caulking off both sides of the stencil before using it again.

    3D Style Wall Art Trees
     
  7. Once you have all your trunks in place, add tree tops and other branches.
     
  8. When adding leaves, keep in mind that you don’t have to use the entire stencil as is. Apply painters tape to close off openings in the stencil to create a smaller grouping. Also flip the stencil over to create leaves that bend in a different direction. Texture the leaves with the knife just as you did the trunks.

    3D Style Wall Art Trees
     
  9. When the caulking is thoroughly set, paint can be applied. For good color effects, determine the direction of the light source in the room. if it’s on the left as in my project, keep this in mind as you paint, making your darkest color on the right of images and lighter color on the left.
     
  10. Fill a small container with a wash made by mixing a little water with the original wall paint. Don’t dilute it too much or you will loose your color. Fleece or other similar fabrics make great paint applicators. Cut two pieces about three inches square, one for adding on, one for wiping away. Dip a portion of one of the pieces in the wash and dab it along the right side of the trunk and leaves. Create variety by painting some leaves with the dark side on the bottom and the light side on top and vice versa. Use the second fleece to wipe away excess or blend the paint from dark side to the light.
     
  11. Add green color accents to the leaves and gold to the trunks. I wanted to use pearl paint for both but couldn’t find colors I liked. Instead I found a pearl pigment powder sold for stamping and scrapbooking. Add a little water to some green powder and use the fleece add on and take away method to stain the right side of the leaves. Wipe away to the left. Add water to the gold powder. Apply the color to the right sides of the trunks. Also add gold color to the edges of the breaks in the trunks. This color is most effective when applied over surfaces painted with the wall color.


 

 

Your Recently Viewed Projects
Love these projects? Get MORE delivered to your Inbox – FREE Click Here!

All fields required.

Rate & Comment

I have not made this yet so I cannot rate it.
Cancel Reply to Comment

Newsletter Signup

Free Newsletter!

Discover crafting projects, free patterns, tips and special offers. Get free craft projects, how-to crafting tutorials & product reviews.

Please Wait

Thanks for signing up

Sorry, we could not sign you up.

Something worth saving?

Register now for FREE to:

  • SAVE all your favorite crafts
  • ADD personal notes
  • QUICKLY reference your crafts

 

Connect with Us

Find us online

  • Facebook
  • Google Plus
  • Instagram
  • Twitter
  • Pinterest
  • Twitter
  • Blog
  • Email
  • RSS

1

© Copyright 2014 Prime Publishing, LLC. All rights reserved.

www.favecrafts.com

close

Images from other crafters

There are currently no images from other crafters.

Was This Helpful?YesNo