Follow Us on Facebook

Get updates from FaveCrafts.com posted directly to your News Feed.

Free Offer
Irish for a Day: St. Patrick's Day Craft and Recipe Guide

Find craft projects to decorate your home, give as gifts and even wear on St. Patrick's Day. Complete the celebration with a collection of St. Patrick's Day recipes.

Bonus: Get our newsletter & special offers for free. We will not share or sell your email address. View our Privacy Policy

(1)

Lucky Clover Pendant Necklace

By:

Swirls of green in friendly plastic make a lovely pendant in the shape of an irish shamrock symbol. Create this clover necklace from AMACO, perfect for St. Patrick's Day with a heart shape cutter and use for other easy jewelry ideas.

Find this project and many more St. Patrick's Day crafts in the 40-page St. Patrick's Day Crafts and Recipes eBook.
 

Green Clover Necklace Pendant


Materials:

  • 3/4” Heart shape cutter (Keep in a small dish of ice cold water with a few drops of oil.)
  • Craft knife
  • Scissor
  • Needle tool
  • 7” Friendly plastic stick: 1 White/white,
  • Adirondack Alcohol inks: Stream, Lettuce, Oregano, Butterscotch
  • Alcohol blending fluid
  • Rubbing alcohol
  • Paintbrush
  • Electric griddle set at 200 to 250 degrees
  • Non-stick baking sheet
  • Envirotex Lite, resin sealer, or any high gloss acrylic sealer
  • Non-stick cookie sheet
  • E6000 Glue
  • Jewelry components and findings of your choice: chain, clasp, bead cap dragonfly connector, pendant connector, jump rings, and 3 small rhinestones.

Directions:

  1. Place the stick of plastic an a protected work surface. I start with a wash of the blending fluid over the plastic stick.
  2. In a random pattern apply drops of lettuce and butterscotch as your background colors. Allow the colors to blend together. Use your paintbrush to fill in any white areas that are left. Clean brush.
  3. Dip the brush into the rubbing alcohol and touch the plastic where you want to create white circles. These circles will resemble puddles.
  4. Mix a drop of stream and butterscotch together to create another shade of green dilute slightly with rubbing alcohol and using the brush apply within the white puddles.
  5. Continue this process until you have attained a pattern you are happy with.
  6. As the final application dip you brush into the rubbing alcohol and splash (splatter) the alcohol across the surface of the plastic. This helps to bread up the design a little more. Allow to dry completely.
  7. Pre-heat the griddle. Place the baking sheet onto the griddle. Place the plastic onto the baking sheet. Allow the plastic to soften.
  8. Remove the pan from the griddle. While the plastic is still warm, cut out three hearts by pressing the cutter into the softened plastic. Be sure to dip the cutter back into the cold water after each cut. This will help keep it from sticking to the plastic. Allow the plastic to cool. Note: You may place the pan under cold running water to speed the cooling process along.
  9. Use the needle tool to press under the edges of the cooled plastic to remove it from the pan. Pop out the ovals. If needed use the craft knife to cut around each one. With your scissor and cut a stem from the remaining plastic.
  10. Apply the Envirotex sealer following the manufactures instructions. Note: I like to place my pieces on a non stick cookie sheet. This way if there is any run off, it will be easy to remove later. Once I have the Envirotex mixed, I like to pour it into a small squeeze bottle. The application will be more precise and much easier. Blow softly, through a straw to pop any bubbles that remain. Allow the resin to dry at least 12 hours. If there has been any run off, remove the piece from the pan by pressing the needle tool under it and lifting it off the sheet. You can cut the excess that has run off with a scissor. Envirotex cures completely in 24 hours.
  11. Place a heart onto your non-stick sheet and heat along the point of the heart with your heat gun to soften the plastic. Now position the other two hearts on either side and press them up against the softened heart. This will form your Clover. Continue to apply heat over the clover, Then add the stem. Continue to heat for a few seconds to secure the bond. Allow to cool completely.
  12. Gather your jewelry components and findings, Position and glue the dragonfly along the top of the clover, so the loop of the dragon extends above the clover. This is going to be your connecting point. Glue on the bead cap and rhinestones. Allow the glue to dry.
  13. Assemble the necklace and attach to the Clover pendant using jump rings.

 

More St. Patrick's Day Jewelry (Celtic, Clovers, and Green):

Four Leaf Clover Charm

Green Heart Key Ring Fob

Green Beaded Shamrock Necklace

Celtic Pendant Necklace Project

 

 

 

 


 

Your Recently Viewed Projects
Love these projects? Get MORE delivered to your Inbox – FREE Click Here!

All fields required.

Rate & Comment

I have not made this yet so I cannot rate it.
Cancel Reply to Comment

Newsletter Signup

Free Newsletter!

Discover crafting projects, free patterns, tips and special offers. Get free craft projects, how-to crafting tutorials & product reviews.

Please Wait

Thanks for signing up

Sorry, we could not sign you up.

Something worth saving?

Register now for FREE to:

  • SAVE all your favorite crafts
  • ADD personal notes
  • QUICKLY reference your crafts

 

Connect with Us

Find us online

  • Facebook
  • Google Plus
  • Instagram
  • Twitter
  • Pinterest
  • Twitter
  • Blog
  • Email
  • RSS

1

© Copyright 2014 Prime Publishing, LLC. All rights reserved.

www.favecrafts.com

close

Images from other crafters

There are currently no images from other crafters.

Was This Helpful?YesNo

[Alt-Text]