Tissue Knit Necklace
By: Hilary Frye
We are adding the craft to your Craft Projects.
The project was added to your Craft Projects.
The Tissue Knit Necklace is a funky spin on the traditional T-shirt necklace, from Hilary Frye. Add a pretty color and some beads to your necklace to make it truly one of a kind with these beaded necklace patterns.
- 1/4 yd. of 60” width tissue knit fabric in white (100% rayon, or 95% rayon/5% lycra)
- 1/4 yd. coordinating batik fabric
- Rotary cutter
- Rotary cutter mat
- Quilting ruler
- Sewing machine
- Jacquard Dye-Na-Flow in 2-3 colors (light/medium/dark values of a coordinating color, they will blend to make Additional colors)
- Rubber bands
- 1” sponge brush
- Paint shirt
- Rubber gloves
- Hair dryer
- Plastic drop cloth
- 2/0 Czech glass seed beads
- Semi-large hole ceramic, polymer clay, or wood beads (approx. 2-3mm inner diameter hole)
- Using your rotary cutter, ruler, and mat; cut your 1/4 yd. of fabric into 18, 3/4” x 30” strips.
- Hold each strip lengthwise by the ends and give it a good full stretch. This will cause the long sides of the strip to curl and roll inwards.
- Put your paint shirt and rubber gloves on. Set-up a plastic drop cloth covered workstation.
- Randomly grab the entire set of 18 strips and scrunch them into a ball shape.
- Take 10 rubber bands and wrap each one around the ball in a random pattern, overlapping as needed to cover the entire ball somewhat evenly.
- Take your lightest color of Dye-Na-Flow and a 1” sponge brush and apply the liquid paint in a random, polka dot fashion over the entire scrunched ball. Remove the rubber bands when done.
- Redistribute the strands into a newly formed scrunched ball. Apply the 10 rubber bands in the same fashion. This time use your medium color of Dye-Na-Flow and the sponge brush to apply a second coat of randomly placed polka dots. (This time you will be covering some white spots and some light colored spots.) Remove the rubber bands when done.
- This step is optional. If you have a third, dark color of Dye-Na-Flow, you can repeat the process.
- Take the painted strands and hang them over the base of a wire hanger to dry. The Dye-Na-Flow should be thoroughly absorbed into the knit fabric. If you have paint dripping from the strands, you’ve used too much paint. Either way, for precaution, put the plastic drop cloth below the strands while they dry. You do not want a permanently stained floor or counter-top.
- The drying process can be done overnight if time allows. Otherwise, to speed-up the process, you can use a hair dryer on a medium heat and air flow setting to dry the strands hanging on the hanger. The strands must be thoroughly dry before you add any beads.
- Bead stringing is done in a random pattern. Using 5-8 beads per strand spaced out somewhat evenly is enough. Clip one end of each strand on a small, 1/2” diagonal to allow for threading the beads. Use a blunt tip needle or tool to poke the pointed end of the strand through the bead. Pull the bead down the length of the strand. Repeat for each bead and each strand until done. (The knit should hold the bead in place. Otherwise, add an overhand knot on each side of the bead to secure it in place.)
- Gather all the pointed ends of the strands together. On the other end gather all the blunt ends.
- Lay these ends flat and facing each other. Push one set of ends 1” in front of the other. (We want the sets overlapping side by side by 1” each side.)
- Using a straight or zig zag stitch, securely sew all the ends together in the center of this overlapping area. You can go over the area repeatedly for extra strength. (Make sure there are no beads in the way of the presser foot and needle before sewing.)
- After sewing, trim the edges clean a 1/4” away from the stitching on each side. Fold one set of ends on top of the set other to form two layers.
- Tear a strip of batik fabric approximately 3” x 12” to wrap over the stitching and bind and hide the edges. (This will become the back of your necklace.) The necklace will be slipped over the head when worn.
- Properly store the necklace by laying it flat in a drawer in acid free tissue paper. Do not wear it while swimming or in the shower. The Dye-Na-Flow should not run. To extend the life and beauty of the necklace, you must take good care of it, just like any of your handmade jewelry.
Your Recently Viewed Projects
Images from other crafters
Love these projects? Get MORE delivered to your Inbox – FREE Click Here!
Report Inappropriate Comment
Are you sure you would like to report this comment? It will be flagged for our moderators to take action.
Thank you for taking the time to improve the content on our site.
- 11 Crochet Shawl Patterns: Crochet Poncho Patterns, Free Easy Crochet Patterns and More
- 12 Knitted Scarf Patterns: Fabulous Free Knitting Patterns for Beginners
- 14 Free Crochet Patterns for Babies and Toddlers
- 16 Free Crochet Hat Patterns, Scarves, and Gloves
- 22 Free Crochet Patterns: Afghan Patterns, Crochet Hats, and More
- 24 Quick and Easy Knitting Patterns
- 7 Adult Coloring Pages
- 8 Free Apron Sewing Patterns
- Easy Lace Knitting Patterns
- Quick & Easy Decoupage: 12 Fabulous Mod Podge Projects for Your Home
Our Newest Projects & Articles
- W. Cushing & Co.
- Cute Crochet Doll
- 45 Quick and Easy Free Knitting Patterns and Beginner Help
- Pastel Peaks Crochet Baby Hat Pattern
- Recycled Crowns from Foil Wrapping Paper
- DIY Butterfly Valentine's Day Card Box Holder
- 44 Easy Craft Projects For Adults
- Quick and Easy DIY Label
- Block Stitch Bun Hat Pattern
- Terrarium in a Mason Jar Gift Idea