Follow Us on Facebook

Get updates from FaveCrafts.com posted directly to your News Feed.

Free Offer
25 Easy to Make Homemade Jewelry Crafts

Quick Crafty and Simple, Perfect for Yourself or Gifts- Find 25 amazing pieces of jewelry to keep for yourself or give as a lovely gesture.

Bonus: Get our newsletter & special offers for free. We will not share or sell your email address. View our Privacy Policy

(1)

Tree of Life Ornament or Pendant

By:

Make a fabulous tree of life ornament to hang in your house, hang on your tree or turn into a pendant for jewelry purposes. Use some fun colored seed beads and make a fun new piece.

Materials:

  • 6mm beads and smaller, including seed beads (see next image)
  • A 4-inch metal ring
  • Two (2) pairs of needle nose pliers
  • A pair of wire cutting pliers
  • Twelve (12) 12-inch strands of 24-gauge wire

The variety of beads used for this particular ornament, including the following: 4mm pearls, 4mm glass rectangle beads, 2 sizes of seed beads, 4mm crystals, 6mm & 4mm faceted glass rounds, and 6mm shaped glass beads.

Instructions:

  1. Take one strand of the wire and thread it through the wire ring, making sure the 2 sides are even. Wrap each side around the ring twice for a total of four coils. Make sure they are pulled tight around the ring.


     
  2.  Repeat step 2 with the remaining 11 wires. Pull all wires to one side of the ring and verify the coils are nice and tight and close together.


     
  3. Start on one side of the wires and begin braiding the first 3 strands. You'll want to create a braid that is approximately 1-inch. Once braided, flip up and move on to the next 3 strands. Continue this process until all wires have been braided. You should end up with 8 braids.


     
  4. Gather the braids as shown in this photo and begin to twist them together.


     
  5. Twist up a little ways until you're ready to separate your first branch. Take 2-4 strands, depending on how thick you want this branch to be, and separate it from the group of wires.


     
  6. Repeat Step 6 until you have the beginnings of a tree with many branches and all of your wires have been used. Personally, I like to split my tree in two at some point and then separate the branches again.


     
  7. Now twist these branches, just like you did the big group of wires, but don't twist them to the ring...yet. You'll want to also start breaking your larger branches into smaller ones. See the picture for ideas on how to break down branches. This is when you'll need to twist the branches to within about 1/4"-1/2" from the ring.


     
  8. Separate the individual wires and make sure they are some-what distributed evenly around the ring. NOTE: If you've twisted the wires too far, do not un-twist them! They will probably break later on! Instead put bends in the branches; this use more wire and pull them towards the center of the ring. (see the final image to see how I did this.)


     
  9. Add a bead or beads to the first wire next to the roots. Wrap the wire around the ring once.


     
  10.  Add another bead to this wire. Wrap again and add another bead. This is to cover the ring from view and make it appear to just be beads. Finish this branch by wrapping it around the ring 3 times, clip off the excess, and pinch tight with pliers.


     
  11. Repeat Step 11 for the remaining wires on this branch. Push the finished section tight against the roots. This will make room for the rest of your branches.


     
  12. Repeat steps 11 and 12 on the other side of the roots. Continue repeating these two steps, changing sides after each branch.


     
  13. Continue this process for the rest of your branches and remember to push them tight against the roots. The last couple branches will be the most difficult because you'll be running out of room on your ring, but this is good because you'll have a nice full tree.

 


OPTIONS:
Pendant Size Tree: If you need to make a smaller Tree of Life for a pendant or even a tiny one for earrings, you'll simply want to use a smaller ring and also decrease the number of wires used. Just remember, you'll always want to have a multiple of three (3, 6, 9...) because you'll be braiding the roots of the tree.
Adding charms: If you'd like to add charms to your tree, just add them while your twisting the branches or before you add beads to the branch, depending on where you want the charm to hang.
Fuller Trees: If you prefer the fuller looking trees, don't twist the branches as close to the edge as I did here. You're beads will then thread closer to the center of the tree and it will appear fuller. The style in this tutorial is just a personal preference of appearance.

Your Recently Viewed Projects
Love these projects? Get MORE delivered to your Inbox – FREE Click Here!

All fields required.

Rate & Comment

I have not made this yet so I cannot rate it.
Cancel Reply to Comment

Newsletter Signup

Free Newsletter!

Discover crafting projects, free patterns, tips and special offers. Get free craft projects, how-to crafting tutorials & product reviews.

Please Wait

Thanks for signing up

Sorry, we could not sign you up.

Something worth saving?

Register now for FREE to:

  • SAVE all your favorite crafts
  • ADD personal notes
  • QUICKLY reference your crafts

 

Connect with Us

Find us online

  • Facebook
  • Google Plus
  • Instagram
  • Twitter
  • Pinterest
  • Twitter
  • Blog
  • Email
  • RSS

1

© Copyright 2014 Prime Publishing, LLC. All rights reserved.

www.favecrafts.com

close

Images from other crafters

There are currently no images from other crafters.

Was This Helpful?YesNo