Custom Explosion Boxes
By: Gary Barbee by Crafter's Companion
We are adding the craft to your Craft Projects.
The project was added to your Craft Projects.
Check out these custom explosion boxes you can use to hold a present for a birthday or special occasion. Put a surprise inside for an explosive gift!
- The Ultimate Crafter's Companion
- Piece of cardstock (varies depending on size of box)
- Scissors and/or paper trimmer
- Decorative paper or extra cardstock
- The first thing we’ll need to figure out is what size explosion box you would like to create. The easiest box to make is a cube and is recommended for this project, but as you get a little more experienced you can play around with odd shaped boxes as an alternative.
- Using these supplied directions you can create explosion boxes as small as a 1” cube all the way up to a 3 1/2” cube in 1/2” increments.
- We will be making a 3 1/2” cube explosion box in this project example. We will be using the “Box Lid” portion on the box making side of the Ultimate Crafter’s Companion Tool. See picture to the right. If you were to measure the spacing between each of these lines, you would notice that they are exactly 1/2” from each other and exactly 1/2” from the edge. This will be important to know as we decide which line to use when scoring our box and matching lid. See example to the right. with measurements shown for each score line.
- Now that you know what size box you want to create, here’s how you figure out what size cardstock to start with. It’s really quite easy. To figure out the starting cardstock size just take the size boxyou want to make and multiply this number by 3. So, if you want to make a 2” cube box you would start with a piece of cardstock that is 6” Square (2” x 3 = 6”). I’ll be making a 3 1/2” box, so I am going to start with a 10 1/2” square piece of cardstock (3 1/2” x 3 = 10 1/2”)
Once you’ve figured out what size piece of cardstock to start with you will then need to decide how many inside layers you will want. I’ll be making 2 additional inside layers, so I will need 2 additional sheets of paper or cardstock. I’ll also be using paper instead of cardstock because I liked what I had laying around design-wise and the outside piece I’ve cut using cardstock will give my box stability.
Take one of these sheets and cut it down to 1/8” smaller than your original sheet of cardstock (10 3/8” Square). Take the last sheet and cut it down to 1/4” smaller than your original sheet of cardstock (10 1/4” Square). You should now have 3 sheets of paper or cardstock that are 1/8” different in size.
Since we are making a 3 1/2” cubed explosion box, we will now need to score the outside layer of our box (10 1/2” square sheet of cardstock) so that we end up with 9 equal sections (3 1/2” per section).
To do this, line up your piece of cardstock up against the top of the board labeled “Box Lid” and score using the 7th line down. The 7th line down is exactly 3 1/2” from the edge of the board (1/2” x 7 = 3 1/2”). Score the same line on all 4 sides of your paper. Take the remaining 2 sheets of paper or cardstock you are using and repeat this same process, using the 7th line down.
Your 3 sheets of paper or cardstock should now look exactly like the picture to the right, comprised of 9 sections, similar to a tic-tac-toe board.
Using the scored lines as your template, cut out the corners of all 3 sheets of your paper or cardstock.
You should end up with 3 pieces that resemble plus signs.
Using scissors or a paper trimmer, cut 1/8” off the 4 ends of your 10 3/8” piece and 1/4” off the 4 ends of your 10 1/4” piece of paper or cardstock.
You should now have a graduated stack of paper or cardstock, with each subsequent layer being 1/8” less than the one below.
Fold in each of the corners on all 3 sheets of paper or cardstock
Apply glue to the middle square of your outside piece of cardstock. (10 1/2” piece)
Adhere your second piece of paper or cardstock to the first. (10 3/8” piece)
Apply glue to the middle of this assembly.
Adhere your last piece of paper or card-stock to your other two assembled pieces. (10 1/4” piece)
Your finished box should now look like this.
If you measure the bottom of your box you will notice that it is exactly 3 1/2”. This is the size lid you will want to create.
To figure out what size cardstock to use for the lid, you will need to ask yourself how deep you want your lid to be; or in other words, how far down you want your lid to hang over the top of the box. In this project I want it to hang down 1 1/2”.
To figure out what size piece of cardstock to start with I will need to add the size of my box base (3 1/2”) to the depth of the box lid, multiplied by 2 (1 1/2” x 2 = 3”). I’ll then add 1/16” to this final number to give my lid a bit of breathing room. Here’s the formula to make it easy for any size square lid:
(Size of the base of your box) + (Depth of your lid x 2) + 1/16” ie. (3 1/2”) + (1 1/2” x 2) + 1/16” = 6 9/16” Square.
Armed with this information I will now cut a piece of cardstock.
Since we have decided to make our lid 1 1/2” deep we will now need to score lines on all 4 sides of our cardstock at exactly 1 1/2” from the edge. Knowing that each line on the “Box Lid” side of our board are exactly 1/2” apart we now know that we will need to score the 3rd line down.
To add a little interest to our lid I have decided to add a decorative embossed edge. To do this I’ll flip the board over to the card making side and dry emboss each of the 4 sides as shown.
When you’re finished, your lid should look something like this.
Trim out a relief in each of the 4 corners as shown to the left using the scored lines from step 14 as your guide. Detailed instructions for assembling a box lid are located in the instruction manual if you need further information.
Now, using the decorative embossed edge as your guide, use a pair of scissors to cut just to the outside of your embossed design. Your finished piece should look like the one shown to the right.
Fold along all of your score lines, including the flaps that will fold in to secure the edges of your box.
Tuck in the flap on each edge and inspect how they meet up with each other.
If the flap shows through the edge of the box, take a pen or pencil and mark the excess.
Using a pair of scissors, trim just inside the marking you just made.
Once you have fitted all of your flaps, use a wet adhesive as shown to put your box together.
It’s also a good idea to use paper clips in the corners while your glue sets.
As a final touch to my box lid I decided to add an embossed heart with a paper insert. To do this I flip my board over to the envelope making side of the board.
Put a corner of your lid into the upstands for the heart and dry emboss.
Next, I took a piece of scrap paper left over from one of the layers of my box and embossed the same heart.
Using a pair of scissors cut this embossed heart out, being sure to cut inside the embossing. This will allow it to fit inside the embossed heart you made on your lid. Use a wet adhesive to glue it on and you’re done! I also used some extra cardstock and paper to add a message on the top of the box as well as another larger embossed heart inside.
To make explosion boxes bigger than what I’ve detailed previously you will still need to follow the basic rule of tripling the finished cube size of your box (ie. To make a 4” cube box you need to start with a piece of cardstock that is 12” Square (4 inches x 3 = 12 inches)). The next all important step is to make sure that a scoreline exists on the board to score the dimension in “Step 2” of these directions. In the case of a 4” box, you would use the line labeled “Half-Fold 8x8” on the card making side of the board.
Your Recently Viewed Projects
Images from other crafters
Love these projects? Get MORE delivered to your Inbox – FREE Click Here!
Report Inappropriate Comment
Are you sure you would like to report this comment? It will be flagged for our moderators to take action.
Thank you for taking the time to improve the content on our site.
- 44 Easy Craft Projects For Adults
- "17 Easy Crafts With Yarn: Make Accessories, Decor and More with Lion Brand Imagine Yarn" free eBook
- Crystal Beads Bracelet
- DIY Guitar Picks
- No Sew Fabric Bookmarks
- Beaded Book Thong
- 5 Homemade Gifts for Boyfriend He Actually Wants
- Made From Scratch Memory Book
- 23 DIY Geeky Gifts for Nerds
- 19 Knockoffs that Will Fool Everyone
- 13 Spring Crafts: Easter Craft Ideas, Spring DIY Home Dcor, and More
- 17 Flower Craft Ideas: How To Make Paper Flowers, Easy Fabric Flowers and More
- 18 Projects Every Crafter Wants
- 23 Fabulous Picnic Craft Ideas + Restaurant Copycat Recipes
- 25 Cool Things to Do with Wine Bottles
- 26 Spring Crafts for Kids
- Easter Craft eBook: Blogger Edition
- Garden Crafts
- Hop into Spring: Easter Crafting and Recipe
- Trash to Treasure: 28 Recycled Crafts
Our Newest Projects & Articles
- Purple Beginner Shawl
- Recycled T-Shirt Quilt Pattern
- Shawl Scarf Crochet Pattern
- Stunning Leather Trimmed Crochet Scarf Pattern
- Knit Look Cowl Crochet Pattern
- Bean Stitch Cowl Crochet Pattern
- Plush Basketweave Baby Blanket Pattern
- "18 Projects Every Crafter Wants" free eBook
- Amethyst DIY Jewelry Box Anthropologie Knockoff
- Retro Gumball Machine Craft