FaveCrafts.com

Menu

Girly Repurposed Shirt Dress

By:

Turn an over-sized men's shirt into a Girly Repurposed Shirt Dress with this step-by-step photo tutorial. This easy and fun sewing project encourages you to reuse something inexpensive or already owned.
 

Dress Finished


Materials:

  • One man's shirt (L, XL or bigger, depends on your own size).
  • Sewing notions – thread, scissors, sewing machine, measuring tape, cutting board, tailor's chalk, straight pins.
  • 0.5-1 yard of coordinating fabric for ruffles.
  • Pin backing
  • Bias tape
  • Buttons

 

Instructions:

  1. Lay your shirt out, cut the sleeves off, rip the pocket, if it has any, cut off the collar and buttons (or you can leave it and then you will have a shirt-dress, which you can tailor closer).

    Men's Shirt
     
  2. To control the depth of the neck and armholes, lay one of your shirts/tanks/tops on the top of it, and draw around it with tailors chalk. Or if you are a pro - use your favorite pattern for the top.
    Cut. Pin the shoulders, try on. Mine looked like this at this stage. Wow! I am wearing a tent!

    Cutting Shirt  Dress Before
  1. Put it on inside out, pin where you want to cut it - tailor to your body (or dress form if you have one), sew together, cut excess and etc.At this point, if you've decided to leave buttons on (maybe changing them for something fancier later), you can mark vertical darts, starting from the highest points of your breasts, and down, and ones on the back - just to make it fit better. I showed it here.

    Pinning for Size
     
  2. I am NOT making a shirt-dress, I've sewn my button part shut, and left the shirt A-shaped.

    Sewing Dress
     
  3. Next - using bias tape, trim your armholes and sew the tape on. Ignore the pleats on the photo, we are not there yet. ;)

    Sewing Bias Tape
     
  4. From sleeves cut as many long strips, as you can - that will be your pleats. I didn't do ruffles, because I think that pleats look a bit more sophisticated.
    I cut my strips about 3 inches wide, then sewn them together at the short edges, pressed the seams open, and ended up with one long loop. I did satin stitch on one edge of my "ruffle" (to do it set your zig-zag at stitch length = 0.5, and stitch width from 2 to 4, I did 3 and liked it), it will give you nice edge, like one you can see on some lingerie. I also hate hemming and don't have a serger, so I use whatever I can.

    Depending on how many pleats you want, measure your neckline, times 2 or 1.5 = how long you want your strip. Which then I folded in half and pinned each end to the shoulders (my dress inside on the loop), edges of both fabrics should be facing in the same direction, and they should be face-to-face!

    Then I marked the center of each part (front and back) and pinned it to the middle of the front/back of my neckline. That way I have equal amount of fabric for each part of the pleated ruffle.
  1. Next - I started to work on my pleats, folding them all in one direction, trying to keep them at the same depth and width. Mind the different fabric in the photo - it is my bottom pleated ruffle, which was made the same way, I just forgot to take picture while working on the neck. Oh, well, I told you, I am not a pro ;). After you are done, fold them down, check on how they lay, adjust, if needed, then stitch them to the neckline.

    Pinning Pleats
     
  2. When done, remove the pins (I remove them as I go on my sewing machine), press them flat, carefully making the folds. Try not to pull it down too hard, or your wrong side of the neckline might be exposed. I also did zig-zag on the inside edge of the pleat, and on the other seams, where I thought it was needed.

    Making Pleats
     
  3. Now cut and hem your bottom part, if you want to leave it like a shirt. You might want to use a belt, but I used a 5.5" ruffle to make it longer (appropriate for wearing like a dress that is even though only with leggins in my case) - fabric was cotton/linen blend, leftover from my floppy hat. I might have made it longer, but I was short on fabric. Anyway - make a ruffle just the way you did on the neckline, only a bit bigger. Sew, fold, press...

    Finishing Pleat
     
  4. I made a flower-pin (which I can move) from two of my fabrics leftovers with buttons in the middle, then chose more buttons, which I've sewn at the front - just like a decoration. That's it!

    Flower Pin
  1. I love it!

    Dress Finished  Dress Finished

 

 See this project and more at Fall Fashion Help: 16 DIY Fall Fashion Trends!

Your Recently Viewed Projects

Love these projects? Get MORE delivered to your Inbox – FREE Click Here!

Ratings & Comments (0)

All fields required.

Rate & Comment

I have not made this yet so I cannot rate it.
Cancel Reply to Comment

Newsletter Signup

Free Newsletter!

Subscribe to our newsletter dedicated to providing the very best healthy meal ideas, cooking tips, healthy recipes & special offers.

Please Wait

Thanks for signing up

Sorry, we could not sign you up.

Something worth saving?

Register now for FREE to:

  • SAVE all your favorite crafts
  • ADD personal notes
  • QUICKLY reference your crafts

 

Connect With Us

Facebook Google Plus Instagram Twitter Pinterest
Twitter Blog Email RSS

About Us Advertise Contact Us FAQs News Keyword Index Privacy Policy Subscribe Terms of Service Unsubscribe

---- 1 ----

close

Images from other crafters

There are currently no images from other crafters.

Was This Helpful?YesNo